How To Fix Car Door Window

Download Article

If one of the ability windows in your vehicle fails to function, it may be the outcome of a broken ability window motor. If you have identified the motor equally the culprit, replacing it is adequately straight forward, though information technology can exist time consuming. It is recommended that you review a service transmission specific to your vehicle when replacing the motor, as the methods used to disassemble car doors tin vary from vehicle to vehicle.

ane
Remove the interior door panel. Almost interior door panels are held in identify with plastic interior fasteners. Y'all can remove these fasteners by pulling on them until they pop out of their holes. Interior panels may likewise be held on with metallic or plastic screws or fifty-fifty bolts.^[1]
- If you lot can't hands identify what kind of fasteners are on your door panel, refer to the vehicle'southward service manual.
- Plow screws or bolts counter clockwise to loosen them, then pull the panel backward off of the door.
2
Gently remove the plastic door cover. Below the door console you will observe a thin, translucent layer of plastic. This cover protects the interior of the vehicle from any water that may splash into the door from above and below. Advisedly pull the door off of the sticky portions that secure it.^[2]
- Try not to tear the embrace every bit y'all volition need to reinstall it after replacing the window motor.
- Replacement covers can be purchased at your local automobile parts store.
Advertisement
iii
Locate the window mounting bolts. Depending on the design of your door, there are a few different places the window mounting bolts may exist, but it should exist fairly apparent when looking into the door. Look for the bolts attaching the window itself to the mechanism that raises and lowers information technology.^[3]
- You may need to use a flashlight to look into the service ports on the door.
- Dissimilar shaped doors will identify the bolts in different locations.
4
Move the window if necessary to access the bolts. In some cases, you may need to raise or lower the window in order to admission the bolts. Plow the key in the ignition of the vehicle without starting the engine to move the window if need be.^[4]
- Raise or lower the window using the power window buttons if possible.
- If the motor is broken, y'all tin can forcefulness the window upwards or downward past paw.
v
Remove the bolts while a friend supports the window. Apply the appropriate sized socket or open concluded wrench to remove the window mounting bolts, but ask a friend to hold the window up as you do to prevent information technology from falling down once information technology's disconnected.^[5]
- You may exist able to hold the window in place equally yous loosen the bolts yourself, but it's dangerous.
- Dropping the window freely could effect in the glass breaking.
6
Raise the window up into the door frame. Take your friend raise the window upward into the door frame equally though you had rolled it up normally. Ask them to hold the window in place until you are able to secure it.^[6]
- Pressing i palm on each side of the drinking glass volition allow your friend to concur the window up.
seven
Use masking record to secure the window in place. With your friend belongings the window upwardly, pull off three or four strips of masking tape that are each about a pes long. Stick the strips to the window on each side over the door frame to concur the window up while y'all work.^[vii]
- Once the window is secured with the tape, you tin can have your friend let go.
- Be sure the tape volition hold the weight of the window before your friend releases information technology.

Advertising

1
Remove the window regulator bolts. The window regulator runs the width of the interior portion of the door and moves back and forth in social club to enhance and lower the window. Find the bolts that agree the regulator to the door and remove them with a socket or open ended wrench.^[8]
- Prepare the bolts aside someplace safety, where yous will easily exist able to determine which bolts were for the regulator.
- Leave the regulator laying inside the door's interior for now.
ii
Locate and remove the window motor mounting bolts. The ability window motor is much smaller than the regulator, merely should be located close by. In virtually applications, the bolts securing the motor to the door are the same size as the regulator mounting bolts. Remove them and fix them someplace safety as well.^[9]
- Fifty-fifty if the bolts have the aforementioned size head, they may not be the same length, so be sure to set them aside separately from the regulator mounting bolts.
iii
Disconnect the motor wiring harness connector. The power window controls adhere to the motor and regulator via a wiring pigtail connector. Press the tab down to disconnect the pigtail then pull them apart to disconnect the motor.^[10]
- Exist careful not to interruption the tab that holds the wiring harness together.
- Pull the pigtail apart at the clip, not on the wires. Pulling on the wires could pull them out of the pigtail.
4
Remove the motor and regulator through the access port. With the pigtail disconnected, the power window motor and regulator will no longer be connected to anything inside the door. Reach into the large access port and pull them each out.^[11]
- The two are connected, and so pulling one will remove them both.
- Be conscientious not to damage the regulator if you lot are simply replacing the motor.
v
Connect the regulator to the new motor. If you are only replacing the power window motor and not the regulator itself, you lot will need to disconnect it and connect information technology to your new power window motor. Visually audit the two to make certain the new motor matches the old 1, then swap the regulator.^[12]
- Different vehicles volition use different methodology to secure the regulator to the window motor.
- Refer to the service manual for your vehicle if you are unsure of how to disconnect the regulator.

1
Slide the new motor and regulator dorsum into place. Insert the ability window motor and regulator back into the main service port in the door in exactly the opposite order that you removed them in when disassembling the door.^[13]
- Orient each component so the holes for the mounting bolts will line up with the holes in the interior of the door.
2
Supplant the mounting bolts. Hold each component in the appropriate position as you return the mounting bolts that secure both the ability window motor and the regulator. Thread each commodities in past hand offset, then use a wrench to tighten them.^[fourteen]
- If a commodities doesn't thread it properly, remove information technology and try again to prevent cross-threading them.
- The bolts don't accept to be extremely tight, but tight plenty to preclude them from vibrating loose every bit you drive.
iii
Reconnect the electrical connector. Once the power window motor and regulator are both mounted securely to the door, connect the wiring from the motor to the pigtail you disconnected previously. This will reconnect the ability window switches and power source.^[15]
- Exist certain the connections fit together. If not, you don't accept the right ability window motor.
4
Remove the masking tape and lower the window back downwards. Ask your friend to concur the window again. Once they are in identify, remove the masking tape that is holding the window upwards in the door frame. Once the record is removed, your friend can lower the window back into the mounting bracket.^[16]
- Make sure your friend has a grip on the window before removing the tape that secures it.
- Y'all tin can use adhesive remover similar Goo Gone on the window if the record left any rest once you are done.
5
Insert the window mounting bolts. Take your friend hold the window in the correct place and so the holes in line up with the holes for the window mounting bolts. Once the window is in place, thread the window mounting bolts in by manus, earlier tightening them with the wrench.^[17]
- Exist sure your friend holds the window in place until the mounting bolts are in place.
- Have your friend let become gradually to ensure the bolts are holding the window properly.
half-dozen
Reinstall the plastic liner and interior panel. Once the window is mounted again, yous tin reattach the plastic interior embrace, and then reinstall the interior panel over the door. Insert the door mounting bolts or snaps to hold information technology in place.^[xviii]
- Once the door is reassembled, reconnect the battery.
- First the engine and test the window.

Advert

Add together New Question

Question

If a regulator has a helper spring on it, practice I need to take the whole regulator out to secure the arms, or tin I replace the motor while it is in the auto?

Depending on the design of the vehicle, yous will likely need to remove the regulator too as the motor when replacing it.
Question

Is the window regulator motor from a 2001 Ford Escape interchangeable with a 2002 Ford Explorer?

They might be. The all-time way to know for sure is to cheque the role numbers for each and run across if they match. If they exercise not, they are not interchangeable.
Question

Where is the fuse located?

The_general_s

Community Answer

Fuses are usually in ane of 3 areas: the engine bay, trunk expanse, near steering wheel.